畢業論文 2zd1556型自定中心園振動篩設計.doc
約39頁DOC格式手機打開展開
畢業論文 2zd1556型自定中心園振動篩設計,摘要振動篩是選煤廠用的最多的設備之一,主要用于煤的準備篩分以及最終篩分用,但是振動篩又是維修量比較大的設備。隨著設計的逐漸完善,自定中心園振動篩能夠很好的解決這一問題。本文主要介紹振動篩在選煤廠中的意義以及振動篩的發展現狀,描述了本次設計2zd1556型自定中心園振動篩設計的計算方法依據和步驟.包括振動篩的分類與特點和...


內容介紹
此文檔由會員 ljjwl8321 發布
摘要
振動篩是選煤廠用的最多的設備之一,主要用于煤的準備篩分以及最終篩分用,但是振動篩又是維修量比較大的設備。隨著設計的逐漸完善,自定中心園振動篩能夠很好的解決這一問題。本文主要介紹振動篩在選煤廠中的意義以及振動篩的發展現狀,描述了本次設計2ZD1556型自定中心園振動篩設計的計算方法依據和步驟.包括振動篩的分類與特點和設計方案的確定;對物料的運動分析,對振動篩的動力學分析及動力學參數的計算,合理設計振動篩的結構尺寸;進行了激振器的偏心塊等設計與計算,包括原始的設計參數,電動機的設計與校核;進行了主要零部件的設計與計算,皮帶的設計計算與校核,彈簧的設計計算,軸的強度計算,軸承的選擇與計算,然后進行了設備維修、安裝、潤滑及密封的設計
關鍵詞:2ZD1556,振動篩,自定中心,設計依據
2ZD1556 CIRCULAR MOTION VIBRATION SIEVE
OF AUTO CENTER
ABSTRACT
Vibration sieve is one of the most widely used devices in Coal Preparation Plant. Mainly used in coal preparation and the final screening with screening, But the vibrating screen is larger than the maintenance of equipment. With the gradual improvement of the design ,circular motion vibration sieve of auto center could well solve this problem. This article mainly introduced that vibration sieve in Coal Preparation Plant significance as well as vibration sieve development present situation, described this time has designed 2zd1556 circular motion vibration sieve of auto center design computational method basis and the step, as well as the main vibration sieve part's choice and the comparison, and showed this design characteristic. Including the classification and characteristics of vibrating screen and determination of design; on the movement of materials analysis, Dynamic analysis of vibration sieve and kinetic parameters calculated, rational design of the structure vibrating screen size; carried out such eccentric Vibrator design and calculation, including the original design parameters, motor design and verification; were the main components of the design and calculation, calculation and check of belt design, spring design calculation, shaft strength calculation, bearing selection and calculation , then the equipment maintenance, installation, lubrication and seal design.
KEYWARDS:2ZD1556,vibration sieve,auto center,design basis
目錄
摘要 I
ABSTRACT II
1緒論 1
1.1 篩分的概念 1
1.2 篩分設備的作用 1
1.3 篩分作業的分類 1
1.4 篩分機械設計的意義 2
1.5振動篩設計的原則 3
1.6篩分機械研究的現狀 3
1.7 將來的發展趨勢 4
2目的依據及說明 4
2.1 2ZD1556自定中心園振動篩設計的目的 4
2.2 設計的依據及參考資料 5
2.3 設計的有關說明 5
3工藝參數的選擇與確定 5
3.1 篩面長度及寬度的確定 5
3.2 生產率的確定 5
3.3 振幅和頻率的選擇 6
3.4 篩面傾角的選擇 8
4動力學分析及參數計算 9
振動篩動力學基本理論 9
4.1 參振重量及參振質量的計算 11
4.2 主彈簧剛度計算與選擇 12
4.3 激振器偏心質量及其偏心距的驗算 13
4.4重心計算 15
5功率計算及電機的選擇 16
5.1 篩分機在負荷狀態下工作所需功率的計算 16
5.2 電動機的選擇 16
5.3 驗算電動機的啟動轉矩 17
6零件的計算 17
6.1 彈簧計算 17
6.2 三角皮帶的傳動計算 18
6.3 軸強度驗算 20
6.4 軸承壽命驗算 24
7基型及結構的選擇 25
7.1 篩分基型的比較和選擇 25
7.2 篩分機結構的選擇和確定 25
8、設備合理的更新期 31
9、結論 33
參考文獻 34
致謝 35
振動篩是選煤廠用的最多的設備之一,主要用于煤的準備篩分以及最終篩分用,但是振動篩又是維修量比較大的設備。隨著設計的逐漸完善,自定中心園振動篩能夠很好的解決這一問題。本文主要介紹振動篩在選煤廠中的意義以及振動篩的發展現狀,描述了本次設計2ZD1556型自定中心園振動篩設計的計算方法依據和步驟.包括振動篩的分類與特點和設計方案的確定;對物料的運動分析,對振動篩的動力學分析及動力學參數的計算,合理設計振動篩的結構尺寸;進行了激振器的偏心塊等設計與計算,包括原始的設計參數,電動機的設計與校核;進行了主要零部件的設計與計算,皮帶的設計計算與校核,彈簧的設計計算,軸的強度計算,軸承的選擇與計算,然后進行了設備維修、安裝、潤滑及密封的設計
關鍵詞:2ZD1556,振動篩,自定中心,設計依據
2ZD1556 CIRCULAR MOTION VIBRATION SIEVE
OF AUTO CENTER
ABSTRACT
Vibration sieve is one of the most widely used devices in Coal Preparation Plant. Mainly used in coal preparation and the final screening with screening, But the vibrating screen is larger than the maintenance of equipment. With the gradual improvement of the design ,circular motion vibration sieve of auto center could well solve this problem. This article mainly introduced that vibration sieve in Coal Preparation Plant significance as well as vibration sieve development present situation, described this time has designed 2zd1556 circular motion vibration sieve of auto center design computational method basis and the step, as well as the main vibration sieve part's choice and the comparison, and showed this design characteristic. Including the classification and characteristics of vibrating screen and determination of design; on the movement of materials analysis, Dynamic analysis of vibration sieve and kinetic parameters calculated, rational design of the structure vibrating screen size; carried out such eccentric Vibrator design and calculation, including the original design parameters, motor design and verification; were the main components of the design and calculation, calculation and check of belt design, spring design calculation, shaft strength calculation, bearing selection and calculation , then the equipment maintenance, installation, lubrication and seal design.
KEYWARDS:2ZD1556,vibration sieve,auto center,design basis
目錄
摘要 I
ABSTRACT II
1緒論 1
1.1 篩分的概念 1
1.2 篩分設備的作用 1
1.3 篩分作業的分類 1
1.4 篩分機械設計的意義 2
1.5振動篩設計的原則 3
1.6篩分機械研究的現狀 3
1.7 將來的發展趨勢 4
2目的依據及說明 4
2.1 2ZD1556自定中心園振動篩設計的目的 4
2.2 設計的依據及參考資料 5
2.3 設計的有關說明 5
3工藝參數的選擇與確定 5
3.1 篩面長度及寬度的確定 5
3.2 生產率的確定 5
3.3 振幅和頻率的選擇 6
3.4 篩面傾角的選擇 8
4動力學分析及參數計算 9
振動篩動力學基本理論 9
4.1 參振重量及參振質量的計算 11
4.2 主彈簧剛度計算與選擇 12
4.3 激振器偏心質量及其偏心距的驗算 13
4.4重心計算 15
5功率計算及電機的選擇 16
5.1 篩分機在負荷狀態下工作所需功率的計算 16
5.2 電動機的選擇 16
5.3 驗算電動機的啟動轉矩 17
6零件的計算 17
6.1 彈簧計算 17
6.2 三角皮帶的傳動計算 18
6.3 軸強度驗算 20
6.4 軸承壽命驗算 24
7基型及結構的選擇 25
7.1 篩分基型的比較和選擇 25
7.2 篩分機結構的選擇和確定 25
8、設備合理的更新期 31
9、結論 33
參考文獻 34
致謝 35
TA們正在看...
- 2012公務員考試申論熱點預測.doc
- t—12拖拉機副變速搖臂機械加工工藝及加工Φ10h8孔...rar
- 證券投資原則、策略與操作方法(ppt44頁).rar
- explorechinauniversityeducationbycomparative.doc
- 現代科技概論_能源和能源技術(ppt40頁).rar
- 基于plc雙電源開關設計(畢業論文).doc
- 財務管理論文某企業現金流量表的財務分析探討.doc
- 財務會計專業畢業論文xx有限公司財務報表分析.doc
- 財政學畢業論文開征物業稅的規劃與設制.doc
- 工程管理畢業論文美國次貸危機對中國房地產市場的...doc