1.1萬字 36頁

摘 要

【摘要】：在日常生活及工業生產過程中，經常要用到溫度的檢測及控制，溫度是生產過程和科學實驗中普遍而且重要的物理參數之一。在生產過程中，為了高效地進行生產，必須對它的主要參數，如溫度、壓力、流量等進行有效的控制。溫度控制在生產過程中占有相當大的比例。溫度測量是溫度控制的基礎，技術已經比較成熟。傳統的測溫元件有熱電偶和二電阻。而熱電偶和熱電阻測出的一般都是電壓，再轉換成對應的溫度，這些方法相對比較復雜，需要比較多的外部硬件支持。我們用一種相對比較簡單的方式來測量。我們采用美國DALLAS半導體公司繼DS1820之后推出的一種改進型智能溫度傳感器DS18B20作為檢測元件，溫度范圍為 -55~125 ºC,最高分辨率可達0.0625 ºC。DS18B20可以直接讀出被側溫度值，而且采用三線制與單片機相連，減少了外部的硬件電路，具有低成本和易使用的特點。

本文主要介紹高精度溫度計的設計。本設計大體分三個工作過程：首先,由DS18b20溫度傳感器芯片測量當前的溫度,并將結果送入單片機。然后,通過 AT89C51單片機對送來的溫度進行計算和轉換,并將此結果送入液晶顯示模塊。最后,由1602液晶顯示器將溫度顯示出來。

【關鍵詞】: 溫度控制、溫度測試、AT89C51、1602LCD、DS18b20溫度傳感器

ABSTRAC

【ABSTRAC】:In daily life and industrial production process, often used in the detection and control of temperature, temperature is the production process and scientific experiments in general and one of the important physical parameter. In the production process, in order to efficiently carry out the production, to be its main parameters, such as temperature, pressure, flow control, etc... Temperature control in the production process of a large proportion. Temperature measurement is the basis of temperature-controlled, more mature technology. Traditional thermocouple and temperature components are the second resistor. The thermocouple and thermal resistance are generally measured voltage, and then replaced by the corresponding temperature, these methods are relatively complex, requiring a relatively large number of external hardware support. We use a relatively simple way to measure. We use the United States following DALLAS Semiconductor DS1820 improved after the introduction of a smart temperature sensor DS18B20 as the detection element, a temperature range of -55 ~ 125 º C, up to a maximum resolution of 0.0625 º C. DS18B20 can be directly read out the temperature on the north side, and three-wire system with single-chip connected to a decrease of the external hardware circuit, with low-cost and easy use.

This paper describes the design of high-precision thermometer. This design generally divided into three work process: First of all, the temperature sensor chip by measuring the current DS18b20 temperature, and the results into the microcontroller. Then, by AT89C51 microcontroller sent to the calculation of the temperature and conversion, and this result into the liquid crystal display modules. Finally, by 1602 the temperature LCD display.

【Key words】: Temperature control、temperature testing、 AT89C51、 1602LCD、DS18b20 temperature sensor

目 錄

第一章 緒論 1

第二章 系統硬件的設計 2

2.1 硬件設計 2

2.1.1功能要求 2

2.1.2方案論證 2

2.2 系統硬件電路的設計..............................................2

2.2.1 AT89C51單片機 2

2.2.1.1 AT89C51簡介及引腳功能說明.......................................2

2.2.1.2 復位電路........................................................4

2.2.1.3 時鐘(晶振)電路 4

2.2.2 1602液晶顯示器 5

2.2.2.1 1602LCD 基本參數及引腳功能說明..................................5

2.2.2.2 1602LCD 指令說明及時序..........................................6

2.2.2.3 1602LCD 標準字符庫..............................................8

2.2.2.4 1602LCD 顯示電路圖..............................................9

2.2.3 DS18b20 溫度傳感器........................................10

2.2.3.1 DS18B20 結構及引腳功能說明.....................................10

2.2.3.2 DS18B20 內部結構...............................................10

2.2.3.3 DS18B20 初始化和讀/寫時序......................................12

2.2.3.4 DS18B20 常用指令...............................................13

2.2.3.5 DS18B20 溫度采集電路圖.........................................14

第三章 系統程序的設計 15

3.1 主程序 15

3.2 DS18B20模塊程序 15

3.3 1602液晶模塊程序............................................... 16

第四章 應用的相關軟件 18

4.1 keil uVision3編輯軟件 18

4.2 Protel 99SE 電路板設計軟件 18

4.3 智能高速通用編輯器 18

第五章 實物效果展示 20

第六章 結論與心得 21

致謝 22

參考文獻 23

附錄A. 高精度溫度計電路原理圖 24

附錄B. 材料清單 25

附錄C. 源程序 26