日韩精品极品视频在线观看免费,天天夜碰日日摸日日澡性色AV,精品国产福利在线观看网址,亚洲第一区欧美国产综合

論文-懸掛運動控制系統.doc

約20頁DOC格式手機打開展開

論文-懸掛運動控制系統,頁數:20字?jǐn)?shù):8055懸 掛 運 動 控 制 系 統摘要本系統根據設計任務要求,采用步進電機作為執行元件,以單片機at89s52作為控制器,利用sh-2h042mb作為步進電機驅動電路,實現對物體位置和運動軌跡的控制。將物體運動坐標轉換為牽引線繩的運動距離,進而轉換成步進電機的步數,實現對物體運...
編號:18-76636大小:670.00K
分類: 論文>其他論文

內容介紹

此文檔由會員 cnlula 發布

論文-懸掛運動控制系統


頁數:20 字?jǐn)?shù):8055

懸 掛 運 動 控 制 系 統
摘 要
本系統根據設計任務要求,采用步進電機作為執行元件,以單片機AT89S52作為控制器,利用SH-2H042MB作為步進電機驅動電路,實現對物體位置和運動軌跡的控制。將物體運動坐標轉換為牽引線繩的運動距離,進而轉換成步進電機的步數,實現對物體運動軌跡的高精度控制。該系統還利用反射式紅外開關實現對物體的運動軌跡的自動跟蹤,它利用安裝在運動物體上一組四個的紅外傳感器來檢測設定運動軌跡(黑線)的位置,單片機將各探頭的信號進行綜合分析處理后,能夠準確判斷出物體偏離黑線的方向,從而控制物體能夠沿著預定的軌跡運動。整個系統設計合理,運行穩定。
Abstract
A motion control system based on step motors is presented. It adopts two step motors as the action components, a single chip computer, the AT89s52, as the controller, and the SH-2H042MB as the driver. It can control the position and the motion trace of the object. The plane rectangular coordinates of the motive object is converted into the length of the tow, and then changed into steps of the stepper motor to control the trace of the motive object accurately. This system can trace the given track automatically with infrared-reflect switches. A group of three infrared-reflect switches mounted on the motive object are used to detect the truck, the black line. The controller analyses the signals from the switches and estimate the error between the object and the truck to control the object motion along the given truck. The system is designed consummately and operated reliably.

一、題目要求和方案論證
任務要求
設計制作一個懸掛運動控制系統,控制物體在傾斜(仰角≤100度)的板上運動。
1)基本要求:
(1)控制系統能夠通過鍵盤或其他方式任意設定坐標點參數;
(2)控制物體在80cm×100cm的范圍內作自行設定的運動,運動軌跡長度不小于100cm,物體在運動時能夠在板上畫出運動軌跡,限300秒內完成;
(3)控制物體作圓心可任意設定、直徑為50cm的圓周運動,限300秒內完成;